Fiber optic new product announcements. Register and submit an announcement.
[An optoXchange website.]
| DXL series optic fusion unit body, maximum make the optic fiber forming, connection and wiring to be high density while offer the best protection for the cable and can be independence fusion connection unit which install in 19 inch standard stander. Feature: Modularize design, frontal operation. Integrate fusion and wiring, maximum high density. Can install in 19 inch standard stander. Suitable for ribbon and non-ribbon cable. Can install many kinds of adapter, such as FC, SC, ST and LC, etc. The adapter and equipment use 30 degree card connecting installment, which ensure the jumping wire’s curvature radius and can avoid the laser to burn eyes. Easy operation, complete protection. The optic fiber and pigtailed all have above 2m saving space. Function target: Environment temperature: -40~ 60 Atmospheric pressure: 70Kpa~106Kpa RH: 40dB; UPC type: >50dB; APC type: >60dB The push-pull durability lifetime of optic connector is greater than 1000 times. |
| DXL series optic fusion unit body, maximum make the optic fiber forming, connection and wiring to be high density while offer the best protection for the cable and can be independence fusion connection unit which install in 19 inch standard stander. Feature: Modularize design, frontal operation. Integrate fusion and wiring, maximum high density. Can install in 19 inch standard stander. Suitable for ribbon and non-ribbon cable. Can install many kinds of adapter, such as FC, SC, ST and LC, etc. The adapter and equipment use 30 degree card connecting installment, which ensure the jumping wire’s curvature radius and can avoid the laser to burn eyes. Easy operation, complete protection. The optic fiber and pigtailed all have above 2m saving space. Function target: Environment temperature: -40~ 60 Atmospheric pressure: 70Kpa~106Kpa RH: 40dB; UPC type: >50dB; APC type: >60dB The push-pull durability lifetime of optic connector is greater than 1000 times. Contact person: Ms. Dailian Phone +86 755 27338117 Email: hnxuxilian@yahoo.com.cn MSN: Dailian80@hotmail.com http://www.dailianxu.com |
| DXL series optic fusion unit body, maximum make the optic fiber forming, connection and wiring to be high density while offer the best protection for the cable and can be independence fusion connection unit which install in 19 inch standard stander. Feature: Modularize design, frontal operation. Integrate fusion and wiring, maximum high density. Can install in 19 inch standard stander. Suitable for ribbon and non-ribbon cable. Can install many kinds of adapter, such as FC, SC, ST and LC, etc. The adapter and equipment use 30 degree card connecting installment, which ensure the jumping wire’s curvature radius and can avoid the laser to burn eyes. Easy operation, complete protection. The optic fiber and pigtailed all have above 2m saving space. Contact person: Ms. Dailian Phone +86 755 27338117 Email: hnxuxilian@yahoo.com.cn MSN: Dailian80@hotmail.com http://www.dailianxu.com |
Product Introduction
IPCE Circuit Simulator is TDM OVER IP Device. As long as the IP address of two terminals can recognize each other, then this device can transmit E1 signal via IP network readezvous point and can achieve join monolithically with existing TDM Terminal, Such as PSTN connection, ATM, Frame relay, ISDN, concentrated user exchange and so on. Provides various operation of TDM directly and don’t need change any Terminal.
Product Feature
1. Transmit frame or unframed E1 signal via IP net, Filly compatible with G.703
2.High transmission rate and low transmission delay
3.Clock revert stably, small dithering and excursion
4.Possess QoS guarantee, supports transmit with date at the same time, assure E1 date prior transmission
5.Convenient to use, don’t need complex setting
6. Transmission package look for address base on IP address and can be configured and revisable
7. Transmission package base on IP date package, shield specific transmission medium, not only can be used in Ethernet /Token-ring or other wired network, but also can be used to increase point to point TDM of wireless LAN. Even can be used in network which mix with wired and wireless
8 Developed a echo counteract device to E1 that it can cancel echo of outside 128ms for some IP transmission network delay is too large and echo problem in voice communication
Setting and Diagnosis
9 IPCE provides menu mode setting service, convenient to use
10 IPCE provides long-distance login connector to set long-distance device via telnet
11 IPCE supports dynamic upgrade, when download new software edition, the old software will be save in backup section. so, if new software be damaged, system can still use old software
12 System provides various alarm: LOS, AIS, LOF and so on
13 IPCE provides local startup auto-inspection, and the inspection result can be observe via super terminal
14 IPCE provides statistic of network affair: date package lose, date package delay, date package wobble and so on
Technologies reference
15 LAN interface:
Port standard: IEEE802.3,IEEE802.3U
Port type: RJ45
Port mode: Auto-adapt to 10/100M
Protocol: CSMA/CD
16 E1 interface:
Line code: HDB3
Bit rate: 2048KBIT/S+-50ppm
Contact person:
Ms. Dailian
Phone +86 755 27338117
Email: hnxuxilian@yahoo.com.cn
MSN: Dailian80@hotmail.com
http://www.dailianxu.com
DVOP04 series of products provide uncompressed high quality transmission systems for 4channeles of digitalized analog video, up to 32 channels of bi-direction date and audio signals,4channels E1/T1 and 10/100M self-adaptive Ethernet date over one single mode or multimode optic fiber, DVOP is a multi-function product which based on highly reliable large-scale specialized ICs designed buy ourselves. It’s extremely flexible with ability to add/drop video.audio,RS232/RS422/RS485,E1,100M Ethernet ports via plugging in/out our field-proven service modulation, DVOP products provide better transmission in quality.
The numerous types of DVOP04 products can meet different user demands. Adopting advanced digital fiber optic transmission technologies, DVOP devices can be installed rapidly without connector(BNC),audio and date connector(RJ45),and fiber optic connector(FC-single or ST-multimode).Users can easily monitor the status of power supply, connector and channels through the indicator lights. There are two types of DVOP04 available: standalone and card-cage packaging.
APPLICATIONS
1.High Way& Toll Station Surveillance
2.Public Security Surveillance
3.Surveillance and cable TV system
4.Intelligent traffic monitoring system
5.High Quality Video Conference
6.Broadcast and TV program transmission
7.Long-distance multimedia teaching
8.Industrial Closed Circuit Television Surveillance
Contact person:
Ms. Dailian
Phone +86 755 27338117
Email: hnxuxilian@yahoo.com.cn
MSN: Dailian80@hotmail.com
http://www.dailianxu.com
| Feature: Four passive transceiver channels in one product. Full-motion CCTV video at distances up to 750ft (225m)when used with passive transceiver. Up to 300ft(1km) with an active receiver. No power required. Exception interference rejection. Built-in polarity protection. Technical Specifications Video |
| Wavelength Division Multiplexing system (WDM) can conserve fiber resources and reduce networking cost. It has solve the problem of lack of fiber and Multi-Service transparent transmission. Be used in MANs assemblage and access layer. Realize construct network and develop operation in short time. OCDA possess advantages of low cost, low power consumption and small size, now it has been used in citywide LAN widely. Now we have developed active CWDM equipment that can run over G.652,G.653, G.655 fiber
Technical index |
The RGB-5000 from Multidyne provides a long haul, transport solution for high-quality, up to 1600 by 1200, high-resolution, RGB or VGA video sources via ONE fiber. The RGB-5000 performs a horizontal gen-lock for a fully synchronous and jitter free high resolution video transport. The system has been upgraded to support a higher quality image at higher resolutions such as 1600 by 1200. The Video and Synch jitter has been reduced to as low as 4 to 5 nano seconds. The net result is a crystal clear image at all resolutions and refreshes rates. The improvements have also extended the operational temperature range to -20 to 60 degrees C.
The RGB-5000 provides a total analog bandwidth of up to 600 MHz. The system 1600 by 1200 pixels are supported over ONE optical fiber. The supports standards include RGB, XVGA, SVGA, UXGA, Component and Analog HDTV signals.
The RGB-5000 has a data throughput of 3.125 Giga Bits per second. Most systems have a 1.25 Gb/s data throughput with 60% compression.
The system automatically detects the Horizontal and Vertical Sync configuration with support for sync on green, CS sync and separate HS and VS sync inputs. The RGB-5000 supports all possible sync configurations with just ONE fiber. Most systems require up to 5 fibers to support all possible sync configurations.
Fiber optic transport provides the capability for the separation of a video signal source and the monitor. For example, a computer or imaging device can be in a different location than the monitors. In many applications space is limited in the monitor area. With flat screen technology, very little space is required. The computers or imaging devices can be in another room. Systems are available to transport RGB video as well as audio, keyboard and mouse control. Application include commodity and stock exchanges, medical and MRI displays, advertising and signs, sporting and concert video displays, video walls, digital cinema, radar displays, air traffic control, military information displays plus many more…
Daisy-chain one RGB/UXGA source to multiple monitors with the NEW MultiDyne RGB-5000-DC RGB/UXGA Fiber Optic Transport Systems with Daisy-Chain. The receiver unit includes an optical repeater to re-transmit the optical RGB/UXGA signal to the next monitor in the chain. Distribute one High Resolution, RGB/UXGA Video signal from one point to multiple points.
Now the user can distribute a high resolution video signal using one fiber optic transmitter to many receivers. The user now can save the cost of duplicate transmitter units, passive and active splitters and add/drop devices. Each RGB-5000-FRX-DC receiver unit includes a fiber optic input and output. Internally the fiber optic input is decoded for the local monitor and then repeated for re-transmission to the next monitor in the chain. The system can virtually repeat a high resolution video signal indefinitely.
The RGB-5000-ET RGB/UXGA Fiber Optic Transport Systems with Ethernet and Data is the latest addition to the Multidyne RGB-5000 Series. Distribute one High Resolution, RGB/UXGA Video signal with 10-BaseT Ethernet and RS232, RS422 or RS485 bi-directional data. The RGB-5000 provides a jitter-free, long haul, transport solution for high-quality, 1900 by 1600, RGB/UXGA via ONE fiber.
Now the user can control the monitor or project from a remote distance. The a high resolution video signal, monitor remote control and network data can now be transported via fiber cable for distances of 200 meters to 40 Kilometers.
For product information and sales, please call MULTIDYNE at 1-(800)-4TV-TEST, 1-(516)-671-7278, FAX 1-(516)-671-3362 or write to the above address. Visit our Web Site at http://www.multidyne.com or send E-Mail to sales@multidyne.com.
Please download a photo at http://www.multidyne.com/pdf/rgb5000frt2.jpg
Please download a data sheet at http://www.multidyne.com/rgb2000.html
5 to 1485 MBps, Multirate, DVB/ASI, SDI & HD-SDI Fiber Optic Transport Link, HD-1500 Series
MULTIDYNE has introduce the NEW HD-1500 Series of 5 to 1485 MB/Sec Serial Digital Video Fiber Optic Transport Link. The product line is intended to ease the engineering and financial difficulties associated with the migration to Digital and High Definition Television. The HD-1500 line will provide an economical solution for the fiber optic transport and distribution of virtually any digital signal from 5 Mbps to 1.5Gbps. The supported standards include SMPTE 292M 1.485 Gbps, SMPTE 259M with operation from 143Mbps - 360Mbps, SMPTE 310M 19.4Mbps, M2S or DVB-ASI 270Mbps, SMPTE 344M 540Mbps and SMPTE 305M SDTi rates.Download this press release at www.multidyne.com/pdf/pressHD1500.pdf
Download a data sheet at http://www.multidyne.com/hdtv.html
Photos: www.multidyne.com/images/HD1500-FRT-NEW.jpg
www.multidyne.com/images/HD1500-FRX-REAR.jpg
Superior Essex has announced the introduction of a new family of Outside Plant fiber ribbon cable products containing between 288 and 1008 optical fibers.
Available in all-dielectric and armored constructions, each of the new fiber cable products utilizes a stranded tube design containing up to 12 fiber optic ribbons per tube and 144 optical fibers per tube. Multiple tubes are combined within the cable to allow for the maximum 1008 total optical fibers.
The new City8 from Pirelli is a carrier-class platform providing high-bandwidth, managed services over a single fiber pair. Pirelli’s CWDM has eight channels with the option to upgrade to 16 and supports time division multiplexing (TDM) and datacom interfaces. Field programmable electronic core and pluggable SFP optical transceivers allow the telecom operator to address all possible network applications. Sub-lambda multiplexing enables the transmission of multiple services over a single wavelength while maintaining transparent client services. (Couldn’t find a photo).
Coastcom, a manufacturer of voice and data communications equipment for public and private networks, announced today it has expanded its product line to include the GigaEdge 8200 next-generation CWDM reconfigurable optical add/drop multiplexer (ROADM) and GigaEdge 2330 mini multi-service provisioning platform (MSPP).
Terawave Communications (www.terawave.com) announced today that it has released its new TW-300 MDU-T broadband passive optical network optical network terminal (BPON ONT) for general availability. This new product allows service providers to provide extremely cost-effective and manageable, multi-service broadband access to apartment buildings, hotels, condominiums, office complexes, shopping centers, and other dense, multi-user sites.
Terahertz Technologies Inc.has announced the introduction of its LTX-5520 Electrical/Optical – Optical/Electrical converter pair. The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fiber optic links ranging from meters to more than 10 kilometers.
ADC recently introduced the Multifiber Service Terminal. The OmniReach Multi-Fiber Service Terminal (MST) incorporates hardened connector technology that is designed to withstand the rugged outside plant environment. These uniquely designed hardened connectors are factory-terminated and environmentally sealed for use in drop cable deployments in optical access networks.
[powered by WordPress.]
To post your product announcement, register first, then login, then go to the "Write" tab, paste your announcement, click "publish", and your announcement is now posted.
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
| by Simple Thoughts | ||||
| M | T | W | T | F | S | S |
|---|---|---|---|---|---|---|
| « Aug | ||||||
| 1 | 2 | 3 | 4 | 5 | ||
| 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| 13 | 14 | 15 | 16 | 17 | 18 | 19 |
| 20 | 21 | 22 | 23 | 24 | 25 | 26 |
| 27 | 28 | 29 | 30 | 31 | ||
22 queries. 0.833 seconds
